Open Concept Remodel: What to Know Before Removing a Load-Bearing Wall

Interior Remodeling

Quick Answer

A load-bearing wall can almost always be removed, but the weight it carries has to be transferred to a properly sized beam and posts that carry the load down to the foundation. That requires a structural design, a construction permit, and inspections in both New Jersey and Pennsylvania. National 2026 cost data puts most projects at roughly $4,000 to $10,000 in a single-story home and $9,000 to $15,000 in a two-story home, before finish work. What runs inside the wall often matters as much as the wall itself.

Taking out the wall between the kitchen and the living room is one of the most requested changes in remodeling, especially in the colonials, split-levels, and ranchers built across South Jersey from the 1950s through the 1980s. Those houses were designed around separate rooms. Opening them up can change how a home feels more than almost any other project, and it is also the project most likely to surprise a homeowner once the drywall comes down.

01

How Can You Tell If a Wall Is Load-Bearing?

A load-bearing wall carries weight from above, such as floor joists, ceiling joists, or the roof, and passes it down to the foundation. A few clues point to one, but none of them is proof. Only a structural engineer or other qualified design professional can confirm what a wall is carrying and specify what replaces it.

Clues that a wall may be load-bearing
What you see What it suggests
The wall runs perpendicular to the floor or ceiling joists above it The joists may be resting on it
A beam, girder, or wall sits directly below it in the basement or crawl space It is likely part of the load path to the foundation
It runs near the middle of the house, parallel to the ridge Common location for a bearing wall in older homes
Another wall sits directly above it on the second floor Loads are probably stacking down through it
Joists overlap or are spliced on top of the wall in the attic or basement The joists depend on the wall for support
It is an exterior wall Almost always load-bearing

Roof framing matters here. Many homes built from the 1970s onward use roof trusses, which span from one exterior wall to the other, so interior walls under them often carry little or no roof load. Older homes framed with rafters and ceiling joists usually rely on a center wall. Even in a truss home, a wall can still carry a concentrated load from a girder truss or a floor above, which is why a quick look in the attic is a starting point and never the final answer.

02

What Permits and Plans Do NJ and PA Require?

Removing a load-bearing wall is structural work, and both states require a permit and inspections for it.

In New Jersey, structural alterations fall under the Uniform Construction Code, administered by your municipal construction office. Plans submitted with a permit application generally must carry the seal and signature of a registered architect or licensed professional engineer, according to N.J.A.C. 5:23-2.15. The code waives the seal only when a single-family homeowner prepares the plans for their own home and signs an affidavit saying so. When a contractor does the work, expect sealed drawings showing the beam size, the posts, and how the load reaches the foundation.

In Pennsylvania, the Uniform Construction Code is enforced by your municipality or the third-party code agency it uses. Philadelphia homeowners work through the Department of Licenses and Inspections. Structural changes require a building permit and inspection there as well, and the drawings will need to show the same load path.

Why the permit protects you

An inspection is an independent check that the beam, posts, and connections match the approved design. Unpermitted structural work also tends to surface at the worst possible moment: during a home inspection when you sell, or when an insurer or lender asks questions. Fixing it after the fact usually means opening finished ceilings back up.

Find Out What Your Wall Is Carrying

Emmons will walk through your home, look at the framing above and below the wall, and explain what opening it up would involve before you commit to anything. Free consultation from our Cherry Hill remodeling team. Call 1-856-885-6677.

Request a Free Remodeling Consultation

03

How Much Does It Cost to Remove a Load-Bearing Wall?

National 2026 cost data compiled from sources including HomeAdvisor, Angi, and HomeGuide puts most load-bearing wall removals at roughly $4,000 to $10,000 in a single-story home and $9,000 to $15,000 in a two-story home. Two-story projects cost more because the beam is carrying a floor, its furniture, and its occupants rather than just a ceiling and attic.

Typical Cost to Remove a Load-Bearing Wall

Single-story home
$4,000 to $10,000
Two-story home
$9,000 to $15,000
$0$4,000$8,000$12,000$16,000
Typical project cost before finish work

National ranges, not a quote. Northeast labor rates often place South Jersey and Philadelphia-area projects in the upper half of each range. Flooring, painting, and kitchen work are separate.

The total is built from a handful of line items, and the spread on each one explains why two quotes for “the same wall” can look so different.

Typical Range for Each Major Line Item

Structural engineer
$300 to $3,000
Permit
$500 to $2,000
Beam installed, 10 to 20 ft opening
$1,000 to $4,000
Rerouting plumbing
$500 to $2,000+
$0$1,000$2,000$3,000$4,000
Typical range per line item

National 2026 ranges. Engineering runs toward the high end when full beam calculations and permit drawings are needed. Permit fees are set locally. LVL beams typically run $50 to $200 per linear foot and steel $100 to $400.

04

How Is a Load-Bearing Wall Actually Removed?

The wall itself comes out quickly. The work that matters happens before and after.

  1. Structural design. An engineer sizes the beam, the posts at each end, and any new footing needed to carry the concentrated load into the foundation.
  2. Permit approval. The sealed plans go to the local construction office for review.
  3. Protection and temporary shoring. Floors and adjacent rooms are protected, and temporary support walls go up on both sides to carry the load while the wall is out.
  4. Demolition and utilities. Drywall or plaster comes off, and whatever runs through the wall is capped, rerouted, or relocated.
  5. Beam and posts. The new beam is set and supported by posts that bear on solid framing and, ultimately, the foundation.
  6. Inspection. The framing is inspected before anything is closed in.
  7. Finish work. Ceilings, walls, flooring, trim, and paint are patched and blended.

The biggest design decision is whether the beam sits flush with the ceiling or drops below it.

Flush beam vs. dropped beam
Flush beam Dropped beam
Appearance Hidden in the ceiling for a seamless look Visible below the ceiling, often wrapped as a design feature
How it works Joists are cut and hung from the beam with metal hangers Joists rest on top of the beam
Cost and labor Higher, with more ceiling work on both sides Lower and faster
When it may not work When the joists are too shallow for the required beam depth When ceiling height is already tight

The posts are the part homeowners rarely think about. A beam collects weight that used to be spread along the whole wall and delivers it to two points. Those points need a continuous path to the foundation, which sometimes means adding blocking inside the floor below or pouring a new footing in the basement.

05

What Could Be Hiding Inside the Wall?

Walls between kitchens and living rooms are rarely empty. Before a price is final, find out what runs through yours.

Plumbing. Supply lines can usually be rerouted. Drain and vent stacks are harder because they need a continuous path to the roof, and moving one can add real cost.

Heating and cooling. Ducts and return air pathways often run through interior walls. Removing them without a plan can starve rooms of airflow.

Electrical and gas. Outlets, switches, and circuits have to be relocated to code, and a gas line running through the wall must be rerouted by a licensed professional.

Lead paint. In homes built before 1978, the EPA’s Renovation, Repair, and Painting rule applies to interior work that disturbs more than 6 square feet of painted surface per room. Removing a wall exceeds that easily. The work must be done by an EPA-certified firm using lead-safe practices, and EPA enforces the rule directly in New Jersey.

Asbestos. Older plaster, joint compound, and duct wrap can contain asbestos. In older homes, have suspect materials tested before demolition starts.

06

Is an Open Floor Plan Right for Your Home?

Open layouts bring in light, let whoever is cooking stay part of the conversation, and make a modest house feel larger. They also come with trade-offs worth thinking through before the wall is gone.

  • Noise travels. The television, the dishwasher, and conversations all share one space.
  • Cooking smells spread. A properly vented range hood matters more in an open plan.
  • Heating and cooling change. One large room behaves differently than two smaller ones, and supply and return locations may need adjusting.
  • Wall space disappears. The wall you remove may be where cabinets, a television, or furniture used to go.

The honest read on how much wall to remove

You do not always have to take the whole wall. Widening an existing doorway into a large cased opening, or leaving a short return at one end, can deliver most of the openness for less money and less disruption. It can also leave room for a vent stack or duct that would be expensive to move. We will show you the options side by side before recommending a full removal.

If you are pairing the wall removal with a new kitchen, plan both together. Island placement, lighting, and flooring all depend on where the beam and posts land. Our kitchen remodeling and design-build teams handle the structural and finish work as one project.

07

What Should You Ask a Remodeling Contractor?

Before you hire for a load-bearing wall

  • Who designs the beam, and will the plans be sealed?
  • Who pulls the permit and schedules inspections?
  • How will the load reach the foundation?
  • What is inside the wall, and is rerouting priced?
  • Are you an EPA Lead-Safe Certified Firm?
  • Does the price include patching floors and ceilings?

A contractor who suggests skipping the permit, or who cannot tell you who is sizing the beam, has answered the most important question already.

How Emmons Approaches Open Concept Remodels

Emmons Roofing & Siding has worked on South Jersey homes since 1989, and our remodeling division operates from a dedicated office in Cherry Hill. Because we also handle roofing, framing, and exterior work, we understand how a house carries weight from the roof down to the foundation, and that is the whole job when a bearing wall comes out.

Engineered, permitted, and inspected. Every load-bearing project starts with a sealed beam design, and we pull the permits and schedule the inspections.
Structure and finish as one project. Our open concept remodels include the beam, utilities, flooring, and finish work, so nothing falls between trades.
EPA Lead-Safe Certified Firm. Certification NAT-F194430-2. In homes built before 1978, our crews contain, remove, and clean up painted materials using the EPA’s required lead-safe work practices.
Licensed and accountable. A member of the National Kitchen & Bath Association (NKBA), licensed under NJ HIC #13VH10633300 and PA #PA149239, and BBB accredited with an A+ rating, with a full workmanship warranty.

Plan Your Open Concept Remodel

Get a free consultation and a clear picture of what removing your wall would involve, cost, and look like. Call 1-856-885-6677.

Request a Free Remodeling Consultation

Frequently Asked Questions

How can I tell if my attic has trusses or rafters?

Look up from the attic floor. Trusses are triangular frames made of smaller lumber, usually 2x4s, with diagonal web pieces connecting the top and bottom, spaced about two feet apart. Rafters are single sloped boards running from the wall to the ridge, typically with separate ceiling joists across the bottom. Trusses usually span the full width of the house, while rafter-framed homes often depend on an interior bearing wall.

What happens to the floor where the wall used to be?

Removing a wall leaves a strip of subfloor where the bottom plate sat, and the flooring on each side rarely matches perfectly. Hardwood can sometimes be woven in with matching boards. Otherwise, many homeowners replace the flooring across the newly combined space so it reads as one room, which should be budgeted from the start.

Can we stay in the house while the work is done?

Usually, yes. The affected rooms are sealed off with dust barriers, and the structural work itself typically takes days rather than weeks. Expect noise, some loss of kitchen use if the wall borders it, and short utility shutoffs while lines are rerouted. In pre-1978 homes, lead-safe containment rules may keep you out of the work area entirely.

Can I remove a load-bearing wall in a townhouse or condo?

Sometimes, but you will need approval from the association first, and in many cases the walls between units are fire-rated party walls that cannot be removed at all. Interior bearing walls inside a townhouse can often be opened with the same engineering and permit process, as long as the association signs off.

Can I remove a load-bearing wall myself?

It is not a job for a DIY project. New Jersey allows a homeowner to prepare plans for their own single-family home, but the beam still has to be sized correctly, the load has to be supported during removal, and the posts have to land on adequate support below. Mistakes here show up as sagging floors, cracked ceilings, or worse, and they are expensive to correct.

About the author: Matt Kelly, Owner

Matt Kelly is the owner of Emmons Roofing & Siding. He took over the company, founded by Keith Emmons in 1989, in 2019 and merged it with his firm Integrity Construction. Emmons now runs residential roofing and siding, commercial, and remodeling divisions from Williamstown, NJ. Last updated .

If you’re located in the Greater Philadelphia Area, South Jersey, or at the Jersey Shore, contact Emmons today for a free quote. Contact Us